Gutter installation cost in Dallas (2026 guide)

What Dallas homeowners pay

Angi’s cost page for Dallas puts most gutter installation projects between $634 and $1,508, with an average of about $1,054. Per linear foot, Angi gives a span of $5 to $30, depending on the material and the gutter style. Gutter guards typically add $906 to $2,071 to a project (average about $1,100), or roughly $6 to $13.50 per foot.

Keep in mind what an average covers. It mixes whole-house systems with short runs over a porch or a garage door. A complete seamless system on a large two-story home, with oversized gutters and a downspout at every corner, usually lands above it. The sample estimate further down shows how the numbers add up.

Dallas prices at a glance

Published figures for orientation only, not quotes. The installer who measures your home gives you the actual price.

Prices by material

Angi’s Dallas page also lists a per-foot price for each common gutter material:

Aluminum is the usual choice for seamless gutters, which are formed on site from a coil in one piece per run. Vinyl is the cheapest line on the list, but it comes in sections with a joint wherever two pieces meet; see seamless vs. sectional gutters. Steel and copper cost more and suit particular homes. Our guide to aluminum, steel, copper or vinyl gutters compares them.

A sample estimate for a one-story ranch

Gutters are sold by the foot, so begin with a tape measure or a satellite map. Add up every eave that needs a gutter, then count downspouts. A common rule of thumb is one downspout for every 30 to 40 feet of gutter. Our guide to measuring your home for new gutters walks through it.

Example only, not a quote: a one-story brick ranch with 160 feet of eave and five downspouts of about 10 feet each.

• 160 feet of seamless gutter at Angi’s Dallas range of $5.50 to $10 per foot: about $880 to $1,600
• 6-inch instead of 5-inch gutters at $1 to $2 more per foot: about $160 to $320
• 50 feet of downspout at $2 to $4 per foot: about $100 to $200
• Guards on all 160 feet at $6 to $13.50 per foot: about $960 to $2,160

That puts the gutters and downspouts at roughly $1,140 to $2,120, and the same job with guards at roughly $2,100 to $4,280. In this example the guards cost about as much as the gutters themselves. Taking down the old gutters, replacing fascia boards that turn out to be rotten and burying drain lines are extra. The range is wide because installers differ in labor rates, metal thickness and hardware, which is the reason to compare written quotes rather than per-foot numbers. See gutter cost per linear foot, explained.

How Dallas compares with other Texas cities

Angi publishes the same kind of local average for other cities we cover. Side by side:

Of the 21 city averages in our gutter cost guide, the Dallas figure of about $1,054 is the fourth-lowest.

What moves a Dallas quote up or down

Hail and metal thickness

North Texas is hail country. National Insurance Crime Bureau figures reported by the trade press show Texas leading the nation in hail-loss claims over a recent three-year period, with more than 25,000 claims in Dallas alone. Hail that bruises shingles also dents thin gutter stock. Heavier aluminum, for example .032-inch instead of .027-inch, or steel costs more per foot but keeps its shape and slope better after a moderate storm. Angi lists galvanized steel at $9 to $15 per foot in Dallas, against $6 to $12 for aluminum. Ask every bidder to write the thickness into the quote. It is the easiest place to cut cost without the customer noticing.

Clay soil and where the downspouts end

Much of the Dallas area sits on Blackland Prairie clay. The Texas Water Development Board describes Houston Black, the state soil, as a clay that shrinks and swells markedly and can open cracks more than 4 inches wide in dry spells. Roof water dumped beside a slab keeps one edge of the foundation wet while the rest dries out. A Dallas quote should therefore say where each downspout discharges. Extensions and splash blocks cost little. Buried lines to a pop-up emitter cost more and are priced as a separate item. See downspout extensions and downspouts and your foundation.

Labor, height and roof shape

Angi reports that Dallas installers charge $50 to $75 an hour, or about $2 to $7 per linear foot, and that labor can climb to $8 to $10 per foot on complex jobs. Two-story walls, steep pitches and cut-up roofs with many corners all add time, because every inside and outside corner needs a miter that is fitted and sealed by hand.

Gutter size

DFW Airport averages 37.01 inches of rain a year (National Weather Service, 1991–2020 normals). That is less than Houston gets, but spring storms can deliver a good share of it in a few hours. On large roof planes and below valleys, 6-inch gutters with 3x4-inch downspouts are a sensible upgrade at about $1 to $2 more per foot. On short runs, standard 5-inch gutters are often enough. See 5-inch vs. 6-inch gutters.

After a hail storm: insurance and timing

When a roof is replaced after hail, the gutters are often part of the same claim, but that is the insurer’s decision and depends on your policy. An installer can document dents with photos and measurements; the adjuster decides what is paid. Hang the new gutters right after the roofers finish, so the fascia can be checked while it is exposed and nobody has to work around a half-done roof. Storm season is also when out-of-town crews go door to door. Take the time to get a second written price, and never sign over an insurance check before the work is done. More in hail-damaged gutters: what to do after a storm and gutter damage and homeowners insurance.

Licenses, permits and paperwork

Texas has no state license for roofing contractors, and none for gutter installers, so there is no state number to look up. That puts more weight on the paperwork you can check yourself:

• Proof of liability insurance
• A written scope: linear feet, gutter size, material and thickness, number and size of downspouts
• Hanger type and spacing. Angi’s spacing guide recommends no more than 3 feet between hangers, and about 2 feet where storms and heavy rain are common
• A price per board or per foot for fascia that has to be replaced
• The workmanship warranty in writing
• A payment schedule that leaves the balance until the job is finished

In the City of Dallas, residential permits run through Development Services (Building Inspection). Gutter work by itself is usually handled as exterior repair, while a full re-roof generally needs a permit. If your job includes fascia or structural repairs, ask the installer and check with the city. Plano, Frisco, Garland, Irving, Richardson and the other suburbs have their own permit offices. See how to choose a gutter contractor.

Where to save, and where not to

• Pair the gutters with the roof. If hail has already put a new roof on the calendar, schedule the gutters right behind it. The fascia is exposed and one setup serves both.
• Order guards in the same visit if you want them. A second trip means a second setup.
• Upgrade selectively. Put 6-inch gutters on the long runs and under valleys, and keep 5-inch where the roof area is small.
• Do not save on thickness or hangers. Thin stock dents sooner, and widely spaced hangers let go sooner.
• Compare the same scope. Two quotes only tell you something if size, thickness, downspouts and guard type match. See how to compare gutter quotes.

Want real prices for your home? One call connects you with an independent installer who serves your ZIP code. Local details and the communities covered are on our Dallas page. Homeowners on the west side of the Metroplex can start at Fort Worth, and the same breakdown for the Gulf Coast is in our Houston cost guide.

Sources

• Angi: How much does gutter installation cost in Dallas, TX?
• Angi: How much does gutter guard installation cost in Dallas, TX?
• HomeGuide: Seamless gutters cost
• HomeGuide: Gutter installation cost
• National Weather Service Fort Worth: DFW 1991–2020 normals
• FenderBender: Texas leads nation in claims for hail damage (NICB data)
• Texas Water Development Board: Houston Black, the Texas state soil
• Angi: How far apart should gutter hangers be?
• City of Dallas: Building Inspection and permits
• Texas Department of Licensing and Regulation (TDLR)